If you’re someone who specifies, installs, or maintains variable frequency drives (VFDs) and motor drives, you’ve probably run into the quiet, frustrating problems that come from bad grounding: erratic drive behavior, random fault codes that don’t make sense, even premature component failures that have nothing to do with overloading or age. For the last 12 years, I’ve worked at a company that supplies new and reconditioned drives and VFDs, and I can’t tell you how many service calls we’ve taken where the root cause was never a faulty drive—it was a botched grounding job. Drives & VFDs

I want to take you behind the scenes here, not just tell you the textbook rules, but the hard lessons we’ve learned from walking through thousands of job sites with electricians, plant managers, and equipment operators. Most people treat grounding as an afterthought, something to tick off a checklist before turning the drive on for the first time. But for VFDs, which convert AC power to DC and back again to control motor speed, they’re prone to high-frequency electromagnetic interference (EMI) and common-mode voltages, and bad grounding turns those into expensive, avoidable headaches.
Let’s start with the basics that people often get wrong: not all grounding is the same. When I hear someone say “just ground it to the main bus,” I know they’re missing half the story. For drives, you actually have two separate grounding systems that work together, but they’re often confused: equipment grounding (EG) and signal grounding (also called control grounding or common-mode grounding). If you mix those up, you’ll end up with ground loops that float, cause voltage spikes, and make your VFD throw a ground fault at random.
First, equipment grounding. This is the bare metal wire that connects the drive’s enclosure, motor, and any associated panels to the building’s main grounding electrode system. The goal here is simple: create a low-resistance path for fault current to flow, so if a hot wire touches the drive’s metal casing, the circuit breaker trips immediately. That’s non-negotiable, per NEC rules, but how you execute it matters. We’ve seen electricians use a 14 AWG copper wire for a 75 HP VFD, and that’s a disaster. NEC requires equipment grounding conductors (EGCs) to be sized based on the drive’s input current, not the wire size of the power leads. For drives, the EGC needs to be at least as large as the drive’s line-side conductor, up to 3/0 AWG, and if you have multiple drives in the same panel, you can’t just daisy-chain the grounds. Daisy-chaining creates high resistance in the path, so a fault current can’t trip the breaker fast enough, leading to shock hazards and drive damage. Instead, each drive’s enclosure should have its own dedicated EGC run directly to the main grounding bar in the electrical room, no splices, no intermediary connections.
Then there’s the part no one talks about enough: the signal ground. VFDs have control circuits, encoder inputs, and communication ports (like Modbus or EtherNet/IP) that run on low-voltage DC signals, usually 5V or 24V. These are super sensitive to common-mode voltage, which is the small voltage difference between the drive’s control ground and the motor’s ground. When that voltage is even a few volts, it can cause noise in the control circuit, leading to the motor speeding up unexpectedly, or the drive losing communication with a PLC. The fix here isn’t just a wire—it’s a dedicated signal ground bus, separate from the equipment ground bus, connected only at one point to the main grounding electrode. That’s called a single-point ground, and it’s the biggest mistake we see on job sites: people connect the signal ground to the equipment ground at both the drive and the motor, creating a ground loop. Ground loops act like an antenna, picking up EMI from adjacent equipment (like welding machines, conveyor drives, or variable speed pumps) and injecting that noise straight into the VFD’s control logic.
I remember a job last year at a food processing plant where we supplied three 150 HP VFDs for conveyor lines. The initial install had each drive’s signal ground connected to its own motor’s ground, and within a week, the drives were throwing “overcurrent” faults at random, even when the conveyors were empty. Our service tech tested the voltage between the drive’s control ground and the motor’s ground and found a 8V common-mode signal. We rewired the signal grounds to a single dedicated bus tied only to the main plant ground, not the motor ends, and the faults stopped. The plant manager told us later they’d spent $12,000 on a new drive before calling us, convinced the original one was defective. That’s the kind of mistake bad grounding causes.
Another common pitfall: grounding to unapproved surfaces. Some electricians will tap into a water pipe for grounding, thinking it’s a solid conductor, but most modern water pipes are plastic inside, so they don’t make a good ground. Even metal water pipes can have corrosion, which raises resistance. We also see people grounding drives to steel structural beams, which work fine for 60Hz fault current, but not for the high-frequency EMI that VFDs generate. High-frequency signals travel better through low-impedance, copper-based paths than steel, so a structural beam can act like a noise antenna instead of a ground. The only approved grounding points for drives are the main grounding electrode system (like ground rods, concrete-encased electrodes, or metal water pipes that are continuous metal and meet NEC requirements) or a dedicated grounding bus in the main electrical panel that’s connected directly to the electrode system.
Don’t forget the motor side, either. It’s not just the drive that needs proper grounding. The motor’s frame must be grounded to the same equipment ground system as the drive, with a conductor sized the same as the drive’s EGC. We’ve seen cases where a motor was grounded to a different panel’s ground bar, which had a higher resistance, leading to voltage differences between the drive and motor. That voltage can leak through the motor’s insulation over time, causing premature motor failure. Also, if you’re using a long cable between the drive and motor (over 100 feet for most VFDs), you need to use shielded cable, and the shield must be grounded at both the drive end and the motor end? Wait, no—let’s get that right. For shielded power cables for VFDs, the shield should be grounded at both ends if you’re dealing with high-frequency EMI, but only if you don’t have a ground loop. Wait, no, let me correct that: if you have a common-mode voltage issue, grounding the shield at both ends creates a ground loop, so best practice is to ground the shield only at the drive end for motors with cables over 50 feet, or use a dual-shielded cable if you need both power and signal shielding. Our team tests cables on our shop floor all the time, and a poorly grounded shield can increase EMI by 10x or more, leading to drive errors.
Another lesson from our service calls: always test your grounds after installation, not before. A lot of people will hook up the power, turn the drive on, and call it a day, but you need to test the ground resistance of the equipment ground path, and the common-mode voltage between the drive’s control ground and the motor’s ground. We carry a simple ground resistance tester that costs less than $200, and it takes 5 minutes to check. If the ground resistance is over 5 ohms, you have a problem. For common-mode voltage, we use a multimeter set to AC volts, measuring between the drive’s control ground terminal and the motor’s frame. If that reading is over 1V AC, you need to adjust your grounding setup. Last month, we had a job at a metal stamping plant where the initial install had 3V common-mode voltage, which was causing the VFD to adjust motor speed randomly. We added a 10uF common-mode capacitor between the drive’s control ground and the main equipment ground, which fixed the issue without rewiring the whole setup.
Wait, let’s talk about when you should use a ground fault protection module, too. A lot of drives have built-in ground fault protection, but that’s for detecting faults, not for proper grounding. If your drive is throwing false ground faults, 9 times out of 10 it’s not the protection module—it’s bad grounding. We see this all the time with new installers who think if the drive says “ground fault,” the ground is bad, but no: a false ground fault is almost always a ground loop or high common-mode voltage. The real danger is a missing or faulty equipment ground, which a false fault code won’t tell you, because the drive is designed to be sensitive to signal noise, not just real fault current.
I also want to address the myth that “more grounding is better.” Some people will run three separate grounds from the drive to the main bus, thinking that will lower resistance, but too many grounds can actually create additional ground loops, especially if they’re run from different paths with different electrical properties. It’s better to have one properly sized, dedicated EGC than multiple undersized or poorly installed grounds.
Let’s wrap this up with a step-by-step checklist we give to every customer when we ship a VFD, to make sure they get the grounding right: 1. Size your equipment grounding conductor to match the drive’s line-side conductor, per NEC 250.122, no exceptions. 2. Run a dedicated EGC for each drive directly to the main grounding bar in the electrical room; never daisy-chain grounds. 3. Create a separate signal ground bus for control circuits, tied only once to the main grounding electrode, not to motor frames or other equipment. 4. Use shielded cable for drives with motor cables over 50 feet, ground the shield only at the drive end to avoid ground loops. 5. Test ground resistance (should be <5 ohms) and common-mode voltage (<1V AC) after installation. 6. Never ground to plastic water pipes, structural steel, or random metal components; only use approved grounding electrodes or dedicated electrical panel ground bars.

I know grounding sounds tedious, but it’s the difference between a VFD that runs for 10 years without issues and one that’s a constant source of downtime and repair bills. At our company, we don’t just supply drives and VFDs—we’ve got a team of technicians who’ve installed and serviced drives in every industry, from food processing to mining to packaging, so we’ve seen every possible grounding mistake, and we can help you avoid them. If you’re planning to install a new drive, troubleshoot a persistent fault code, or just want to make sure your existing grounding is up to code, reach out to our team to connect with our purchasing and technical support staff. We’ll walk you through your specific setup, answer your questions, and make sure your drives are grounded properly, so you can spend less time fixing problems and more time running your operation.
Sensors & Safety References
- National Electrical Code (NEC) 2023, Article 250: Grounding and Bonding.
- Harmonic Balance Inc. “Grounding and Bonding for Adjustable Frequency Drives”, 2021.
- Allen-Bradley “VFD Grounding Best Practices”, Rockwell Automation Technical Publication, 2022.
- International Electrotechnical Commission (IEC) 61800-5-1: Adjustable speed electrical power drive systems – Part 5-1: Safety requirements – Electrical, thermal and energy, 2017.
- Siemens “Best Practices for Grounding and Shielding VFD Installations”, 2020.
Xiamen Shengcheng Automation Co., Ltd.
As one of the most professional drives & vfds suppliers in China, we offer a wide range of products with superior quality. Please rest assured to buy bulk discount drives & vfds from our factory. For price consultation, contact us.
Address: Room 1104, Building A, No.1 Golden Bay Fortune Center, No. 999, Anling Road, Heshan Street, Huli District, Xiamen City, Fujian Province, China
E-mail: sales@cn2014.com
WebSite: https://www.autelectrical.com/